300-135选择题全变，仅凭我的记忆发布内容

YhuY

haizi595610 please share full new question and answer ?

YhuY

haizi595610 发表于 2018-6-25 10:45
' j3 H; O# q& k2 }, f* P" S- g+ I楼主看看你遇到的是不是这些题目。
6 ]' ]7 ]7 j5 s  X& ]# |
How do you secure the management plane?

% i+ [% `; `! o# a, hhaizi595610 please share full new question and answer ?

deanke

加油

colorzoo

謝謝分享

pointx123

楼主考过了~恭喜楼主
小弟七月也要考，希望题库别差太大><

Zanzan11

变难了啊…

as8818165

都是要多学题库，多了解一下，考前也要认真看看，多看论坛分享

Rockyw

路过了解一下！

閒人中心

感謝分享

tifayuna

謝謝大大分享

titanic0101

titanic0101

titanic0101

haizi595610

楼主，这是部分选择题的问题，请自行查找答案，希望对你有帮助。
9 g' v& }% [7 M0 n* F
Q.1
' h/ R: k5 r9 o. ?8 zTroubleshoot uRPF loose mode at client gateway router for networks that are not in the routing table. (Choose two)
a.        Dynamic routing is configured on the router
8 Q3 E2 r5 \; L' C- H% @+ S5 A' ?b.        CEF is enabled on the router
c.        allow-default is configured for loose mode
d.        CFE is disabled on the router
4 R: K* u( l2 l, Z0 e  \3 A& o3 ke.        Static Routing is configured on the router
5 x( I6 U! @4 ^1 G, I  w7 p
- K2 ]" j# m) B* R. AQ.2
: Y& G4 l3 T: PWhich two can use to protect & secure management plane from unwanted & unauthorized access ?
) A& L. E) W! V- ha.        Limit physical access to network devices
b.        Use RADIUS instead of TACACS+ for AAA
c.        Create an ACL to permit Telnet access only
5 M4 b. l0 d8 e4 td.        Enable authentication for the routing protection
e.        Use MPP to limit the interfaces on which management traffic  can traverse the device
& V9 J# ~. u, G
, U* K% M: j/ O. ^1 IQ.3
Which command enables authenticated login if a TACACS+ failure occurs ?
* x7 ?6 B7 O! e6 J6 i9 r" V  [a.        aaa authentication login test group local tacacs+
b.        aaa authentication login test group tacacs+ local
6 {8 H6 p$ Z( p# R8 f: P* W$ i, Kc.        aaa authentication login test group radius local
d.        aaa authentication ppp dialins group tacacs+ local
9 n: j( b0 p1 R' s9 K
1 O0 N2 \' N- A) g/ ~6 IQ.4
# _. p8 f* I" w' o6 b6 lWhen your network experiences Cisco Discovery Protocol and LLDP issues, with which layer of the OSI model must you begin troubleshooting ?
$ o6 ^. h$ B% j7 _# ^# D" va.        datalink layer
b.        physical layer
- C+ s) y: F1 o4 T3 Q3 `, Kc.        network layer
# J0 O, F, W0 H; u' rd.        transport layer

: j& M2 K2 |" u/ k& R* b) H1 U& T' MQ.5
$ i1 W/ X( a4 U% c$ y& L& \Restrict access for device on  management plane? (choose two)
A. enable Cisco Express Forward (CEF) globally
B. Add authentication for routing protocols
C. Restrict physical access
0 q5 g+ [9 Q/ o5 [D. Add ACLs for telnet
, c- e8 M6 v  z5 M6 w& h& w
Q.6
CDP and LLDP are not working properly, where do you start troubleshooting?”A. Physical
B. Datalink
! w0 i" `- w' i4 VC. Network
' U. X4 `! V. C! ?! |5 X; ND. Transport

byronyj

感謝樓主！
1 B- f8 v: v% A& y再接再厲！