300-135选择题全变，仅凭我的记忆发布内容

YhuY

haizi595610 please share full new question and answer ?

YhuY

haizi595610 发表于 2018-6-25 10:45
3 v" A* s/ M  R$ |% }9 u楼主看看你遇到的是不是这些题目。

How do you secure the management plane?

haizi595610 please share full new question and answer ?
4 B5 P+ a8 `5 \. o8 ]

deanke

加油

colorzoo

謝謝分享

pointx123

楼主考过了~恭喜楼主
小弟七月也要考，希望题库别差太大><

Zanzan11

变难了啊…

as8818165

都是要多学题库，多了解一下，考前也要认真看看，多看论坛分享

Rockyw

路过了解一下！

閒人中心

感謝分享

tifayuna

謝謝大大分享

titanic0101

titanic0101

titanic0101

haizi595610

楼主，这是部分选择题的问题，请自行查找答案，希望对你有帮助。
) A6 A* j* X8 u. `: C% k
Q.1
. N+ h- r+ P9 }* H2 d4 d$ `Troubleshoot uRPF loose mode at client gateway router for networks that are not in the routing table. (Choose two)
a.        Dynamic routing is configured on the router
b.        CEF is enabled on the router
- K) z- j9 M, i. c, {' Pc.        allow-default is configured for loose mode
: V4 t+ o0 g" I. ?0 a9 kd.        CFE is disabled on the router
; y5 C" `2 q* M3 }6 p2 Y: ke.        Static Routing is configured on the router

' D% u+ ^3 @8 B1 Y+ HQ.2
Which two can use to protect & secure management plane from unwanted & unauthorized access ?
a.        Limit physical access to network devices
/ F# U  K  K' D4 L% e% Vb.        Use RADIUS instead of TACACS+ for AAA
c.        Create an ACL to permit Telnet access only
/ t2 \: W, H4 b% J) Pd.        Enable authentication for the routing protection
0 J  u5 w9 e+ m$ F4 R$ J$ te.        Use MPP to limit the interfaces on which management traffic  can traverse the device

Q.3
Which command enables authenticated login if a TACACS+ failure occurs ?
; U6 \5 h& r) I# c# z5 A/ _" Sa.        aaa authentication login test group local tacacs+
b.        aaa authentication login test group tacacs+ local
c.        aaa authentication login test group radius local
d.        aaa authentication ppp dialins group tacacs+ local
) S2 A7 B* }1 y2 e9 V2 {0 I
/ ^( h0 P7 R; Q) o& ?2 P( Y) vQ.4
When your network experiences Cisco Discovery Protocol and LLDP issues, with which layer of the OSI model must you begin troubleshooting ?
8 |- h7 p: A  m' P5 H; h, W& j; Na.        datalink layer
b.        physical layer
' N0 l1 O1 W+ `  G% E4 @6 Hc.        network layer
* K0 E3 s' k, d- M: v8 Qd.        transport layer

Q.5
: ~9 C: V8 |/ {- r; Y5 ZRestrict access for device on  management plane? (choose two)
A. enable Cisco Express Forward (CEF) globally
B. Add authentication for routing protocols
C. Restrict physical access
  C0 s* _$ u" {) ^3 cD. Add ACLs for telnet
& f! A  M( F" f) b& h# ]
4 D6 t+ H  I3 ?3 Q9 S$ c7 ^Q.6
! o5 m6 r: D5 UCDP and LLDP are not working properly, where do you start troubleshooting?”A. Physical
B. Datalink
C. Network
D. Transport

byronyj

感謝樓主！
再接再厲！