CCNA LAB 91: Configuring Back-to-Back Serial Connections

小乔

Lab Objective:
The objective of this lab exercise is to configure back-to-back Serial interfaces between two Cisco routers. By default, router Serial interfaces receive their clocking information from an external device such as a CSU/DSU.

Lab Purpose:
Back-to-back Serial interface configuration is a fundamental skill. Because routers typically receive clocking from an external device such as a CSU/DSU, it is imperative to understand how to bring up a back-to-back Serial connection between two routers to set up your home lab, for example. As a Cisco engineer, as well as in the Cisco CCNA exam, you will be expected to know how to configure back-to-back Serial connections.

Certification Level:
This lab is suitable for both CCENT and CCNA certification exam preparation.

Lab Difficulty:
This lab has a difficulty rating of 3/10.

Readiness Assessment:
When you are ready for your certification exam, you should complete this lab in no more than 10 minutes.

Lab Topology:
Please use the following topology to complete this lab exercise:



Task 1:
Configure hostnames on R1 and R2 as illustrated in the topology.

Task 2:
Enable Serial interfaces on R1 and R2. The Serial0/0 interface on R2 is identified as the DCE in the topology. Use the appropriate show command to verify that this interface is indeed the DCE.

Task 3:
Configure the DCE interface on R2 to provide clocking to R1. The clock speed should be 256 Kbps. Remember that 1 Kbps = 1000 bps. Verify that R1 receives clocking information from R2.


Task 4:
Configure IP addressing on R1 and R2 Serial0/0 interfaces as illustrated in the topology.

Task 5:
Verify your interface status and ping between R1 and R2 to validate connectivity.

Configuration and Verification
Task 1:
For reference information on configuring hostnames, please refer to earlier labs.

Task 2:
R1(config)#interface serial0/0
R1(config-if)#no shut
*Mar  1 00:36:47.282: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
R1(config-if)#end
R1#

R2(config)#interface serial0/0
R2(config-if)#no shut
*Mar  1 00:36:47.282: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
R2(config-if)#end
R2#show controllers serial 0/0
Interface Serial0/0
Hardware is PowerQUICC MPC860
DCE V.35, no clock
NOTE: The show controllers  command will tell you whether the interface is the DCE side (which provides the clocking) or the DTE side (which receives the clocking) on a particular router interface. Note that GNS3 doesn’t use actual cables so there is no need to configure clocking.

Task 3:
R2#conf t
Enter configuration commands, one per line.  End with CTRL/Z.
R2(config)#interface serial0/0
R2(config-if)#clock rate 256000
R2(config-if)#end
R2#show controllers serial0/0
Interface Serial0/0
Hardware is PowerQUICC MPC860
DCE V.35, clock rate 256000

R1#show controllers serial0/2
Interface Serial0/0
Hardware is PowerQUICC MPC860
DTE V.35 TX and RX clocks detected.
Task 4:
For reference information on configuring IP addressing, please refer to earlier labs.

Task 5:
R1#show ip interface brief
Interface     IP-Address     OK? Method Status                Protocol
Serial0/0     172.30.100.1   YES manual up                    up

R1#ping 172.30.100.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.30.100.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/8/12 ms

R2#show  ip interface brief
Interface   IP-Address     OK? Method Status                Protocol
Serial0/0  172.30.100.2    YES manual up                    up

R2#ping 172.30.100.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.30.100.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/8/12 ms



来源: CCNA LAB  90: Configuring EIGRP for IPv6

lxzhanshe

谢谢楼主分享！

jackdp

谢谢楼主分享！

新野

看看，谢谢！！！

lxzhanshe

谢谢分享