更改Linux系统的网卡名称

LinuxProbe

一、网卡配置文件名称重命名为eth0 (也可以改为其他名称)
[root@Jaking11 ~]# ifconfigens33: flags=4163  mtu 1500        inet 192.168.10.11  netmask 255.255.255.0  broadcast 192.168.10.255        inet6 fe80::250:56ff:fe29:eae  prefixlen 64  scopeid 0x20        ether 00:50:56:29:0e:ae  txqueuelen 1000  (Ethernet)        RX packets 132  bytes 14492 (14.1 KiB)        RX errors 0  dropped 0  overruns 0  frame 0        TX packets 115  bytes 13105 (12.7 KiB)        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0lo: flags=73  mtu 65536        inet 127.0.0.1  netmask 255.0.0.0        inet6 ::1  prefixlen 128  scopeid 0x10        loop  txqueuelen 1000  (Local Loopback)        RX packets 140  bytes 11204 (10.9 KiB)        RX errors 0  dropped 0  overruns 0  frame 0        TX packets 140  bytes 11204 (10.9 KiB)        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0[root@Jaking11 ~]# [root@Jaking11 ~]# cd /etc/sysconfig/network-scripts/[root@Jaking11 network-scripts]# lsifcfg-ens33  ifdown-ppp       ifup-eth     ifup-sitifcfg-lo     ifdown-routes    ifup-ippp    ifup-Teamifdown       ifdown-sit       ifup-ipv6    ifup-TeamPortifdown-bnep  ifdown-Team      ifup-isdn    ifup-tunnelifdown-eth   ifdown-TeamPort  ifup-plip    ifup-wirelessifdown-ippp  ifdown-tunnel    ifup-plusb   init.ipv6-globalifdown-ipv6  ifup             ifup-post    network-functionsifdown-isdn  ifup-aliases     ifup-ppp     network-functions-ipv6ifdown-post  ifup-bnep        ifup-routes[root@Jaking11 network-scripts]# mv ifcfg-ens33 ifcfg-eth0[root@Jaking11 network-scripts]# vim ifcfg-eth0 TYPE=EthernetPROXY_METHOD=noneBROWSER_ONLY=noBOOTPROTO=staticDEFROUTE=yesIPV4_FAILURE_FATAL=noNAME=eth0DEVICE=eth0ONBOOT=yesIPADDR=192.168.10.11GATEWAY=192.168.10.2NETMASK=255.255.255.0二、禁用网卡命名规则

此功能通过

/etc/default/grub

文件来控制，要禁用此功能，在文件中加入

"net.ifnames=0  biosdevname=0"

即可

[root@Jaking11 network-scripts]# vim /etc/default/grub  GRUB_TIMEOUT=5GRUB_DISTRIBUTOR="$(sed 's, release .*$,,g' /etc/system-release)"GRUB_DEFAULT=savedGRUB_DISABLE_SUBMENU=trueGRUB_TERMINAL_OUTPUT="console"GRUB_CMDLINE_LINUX="crashkernel=auto rd.lvm.lv=centos/root rd.lvm.lv=centos/swap rhgb quiet net.ifnames=0 biosdevname=0"GRUB_DISABLE_RECOVERY="true"三、添加udev网卡规则

在/etc/udev/rules.d目录中创建一个网卡规则70-persistent-net.rules文件，在文件中写入以下参数：

SUBSYSTEM=="net",ACTION=="add",DRIVERS=="?*",ATTR{address}=="需要修改名称的网卡MAC地址",ATTR｛type｝=="1" ,KERNEL=="eth*",NAME="eth0"

参考配置：

[root@Jaking11 rules.d]# vim 70-persistent-net.rulesSUBSYSTEM=="net",ACTION=="add",DRIVERS=="?*",ATTR{address}=="00:50:56:29:0e:ae",ATTR｛type｝=="1" ,KERNEL=="eth*",NAME="eth0"执行grub2-mkconfig -o /boot/grub2/grub.cfg命令生成更新grub配置参数
[root@Jaking11 rules.d]# grub2-mkconfig -o /boot/grub2/grub.cfgGenerating grub configuration file ...Found linux image: /boot/vmlinuz-3.10.0-957.el7.x86_64Found initrd image: /boot/initramfs-3.10.0-957.el7.x86_64.imgFound linux image: /boot/vmlinuz-0-rescue-fe49b659ccb940fa8d260a5897c0b08aFound initrd image: /boot/initramfs-0-rescue-fe49b659ccb940fa8d260a5897c0b08a.imgdone重启Linux系统后验证网卡名称是否更改成功
[root@Jaking11 ~]# ifconfigeth0: flags=4163  mtu 1500        inet 192.168.10.11  netmask 255.255.255.0  broadcast 192.168.10.255        inet6 fe80::250:56ff:fe29:eae  prefixlen 64  scopeid 0x20        ether 00:50:56:29:0e:ae  txqueuelen 1000  (Ethernet)        RX packets 86  bytes 10889 (10.6 KiB)        RX errors 0  dropped 0  overruns 0  frame 0        TX packets 95  bytes 10828 (10.5 KiB)        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0lo: flags=73  mtu 65536        inet 127.0.0.1  netmask 255.0.0.0        inet6 ::1  prefixlen 128  scopeid 0x10        loop  txqueuelen 1000  (Local Loopback)        RX packets 0  bytes 0 (0.0 B)        RX errors 0  dropped 0  overruns 0  frame 0        TX packets 0  bytes 0 (0.0 B)        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0总结

以上就是更改 RHEL7 或者 CentOS 7 的网卡名称的方法，最后看到 eth0 说明网卡名称更改成功！

xz蓝精灵

666

wellhopehxr

看上去好乱~~~~~~~~~~~~