5月20日300-135 上海 1000 PASS

xzjxiaomao

选择和拖图全是题库里的，那道spanning tree的选择题选bottom-up。
TT题有一道新的，前面的战报中也有提到：
2 f8 @2 @3 j: N7 qclient1拿得到地址，但ping不通网关，不是DSW1上做了vlan filter（vlan filter我也考到了），而是ASW1上连client的接口配置成了trunk。
NP收官了，感谢论坛里的各位！

newbie13

新TT第二問題,是選擇咩錯誤

lzr023

感谢分享，恭喜啦

as8818165

恭喜，恭喜

tony1104

請教一下ASW1 TT變化題是這題嗎?謝謝&恭喜
  `$ s& c/ w4 `. O
Configuration on ASW1
Interface FastEthernet1/0/1
* \% x) h3 [$ V  J1 u- fswitchport mode access
switchport trunk encapsulation dot1q
9 A6 q$ r: q- [+ `: nshutdown
5 @- b' l% v' I8 g4 G: F, I6 I!
nterface FastEthernet1/0/2
switchport mode access
switchport trunk encapsulation dot1q
shutdown
- F; M- t( f$ f1 k# y, C; v8 l
QUESTION 1
On which device is the fault condition located?
A. DSW1
B. ASW1
C. Client 1
. C: [* g' K3 W/ n1 Y( dD. FTP Server
Correct Answer: B

Section: TROUBLE TICKET
Explanation
( R- _3 r( w9 ~7 t7 T6 nExplanation/Reference:
' \1 K9 X6 e) c& V" {Explanation:
4 k  L$ l  b1 F$ `" d6 eSince the Clients are getting ip 169.x.x.x, we know that DHCP is not working.
( _  W1 X  l+ R+ @  I2 IHowever, upon closer examination of the ASW1 configuration we can see that
the problem is not with DHCP, but the fact that the clients have been
configured for the wrong VLAN. According to the network diagram, these
clients should be in VLAN 10, not VLAN 1 so the problem area is the
configuration of ASW1.
1 r+ J2 X) X$ ?1 E
7 U- N9 }6 [' F* u. \% g
8 q* p& m3 y" f: |  SQUESTION 2
0 G) Q, [: Z" [The Fault Condition is related to which technology?
A. NTP
4 G- S5 @) E" O5 Z+ [8 P! ~B. Switch-to-Switch Connectivity
C. Loop Prevention
D. Access Vlans
6 g' [* D4 S6 WE. VLAN ACL Port ACL
8 q  r0 [' T5 I' g6 }/ |$ ?F. Switch Virtual Interface
4 v0 o" B) o5 w* J3 }+ R4 ZG. Port Security
Section: TROUBLE TICKET
* _+ R, I2 N; {$ _% U: lExplanation
4 K* J' [: Y4 s2 ]$ A0 L* hExplanation/Reference:
  A* [4 T! V0 qExplanation:
. u6 @( w& W. C1 L' eSince the Clients are getting ip 169.x.x.x, we know that DHCP is not working.
- H9 n8 q- K9 YHowever, upon closer examination of the ASW1 configuration we can see that
the problem is not with DHCP, but the fact that the clients have been
configured for the wrong VLAN. According to the network diagram, these
( z5 M2 H' k5 q, m( \. p4 X% f6 dclients should be in VLAN 10, not VLAN 1. So the problem is related to VLAN.
5 p7 I, V+ L' q; F9 G3 D; ?

QUESTION 3
1 {" t+ m3 i9 M) I0 R5 C2 u* pWhat is the solution of the fault condition?
A. In Configuration mode, using the interface range Fastethernet 1/0/1 -2,
" }, B( z: }. e& j) xthen switchport mode access vlan 10 command
9 C) ~2 @) j% {' Q+ ~B. In Configuration mode, using the interface range Fastethernet 1/0/1 -2,
then switchport access mode vlan 10 command
2 p- l  z4 f6 u3 fC. In Configuration mode, using the interface range Fastethernet 1/0/1 -2,
then switchport vlan 10 access command.
D.In Configuration mode, using the interface range Fastethernet 1/0/1 -2, no
switchport trunk encapsulation dot1q，then switchport access vlan 10 ，
and no shutdown,command.
Correct Answer: D

lambyZzz

恭喜大大 , 厲害

alanlaoda

恭喜過關

trowal

恭喜樓主

trowal

恭喜樓主

trowal

恭喜樓主

art7rainbow

congratulations
2 G$ [/ s9 {8 P/ D

kingswayatcisco

congrats and thanks for sharing