- 积分
- 217
- 鸿鹄币
- 个
- 好评度
- 点
- 精华
- 最后登录
- 1970-1-1
- 阅读权限
- 30
- 听众
- 收听
初级工程师
  
|
思科2811路由器无法正常启动,直接进入rommon模式。改了寄存值和重灌IOS,都没能解决。好像是认不到Flash,拆其它2811上的Flash上去,也是一样。设备是不是坏了,还能救吗?以下是设备启动信息:
P$ K8 F6 p- m: U( Z! O1 M7 o! K8 l( u$ e
System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
# x2 u# |1 T: P$ D$ I4 Z3 vTechnical Support: http://www.cisco.com/techsupport4 X( S; z3 ^0 `, s% r s) p6 }- `
Copyright (c) 2004 by cisco Systems, Inc.& }! k. ?: }+ \) b3 v( f
2 T% `8 b& m# J8 ]5 K: h* s
Initializing memory for ECC* m5 ]- o" u0 u
.7 L, l, K4 d- y) T/ f5 [$ x: O
c2811 processor with 262144 Kbytes of main memory1 g# f* e5 G" V3 D0 Q
Main memory is configured to 64 bit mode with ECC enabled
9 H5 J' J/ p! _; u4 S
6 ]* x: _; j, j& m# G4 U( e/ K2 D
6 ~& F+ A& ^+ [$ Z4 uReadonly ROMMON initialized3 v* W( P3 D5 f5 V: |; m* [2 r
boot: cannot open "flash:"+ s- y# K% N4 r' [# _% `( Y8 ?5 v4 X
boot: cannot determine first executable file name on device "flash:"6 }9 o7 X! U/ c/ F4 Y! [% Z
c2811 processor with 262144 Kbytes of main memory! H- x, `; U6 Z8 Z% W8 R, x
Main memory is configured to 64 bit mode with ECC enabled
& \! _' L, I) k* ]& P8 S
9 Q4 j* @$ I( w
: f, s1 c7 u, m. V# y$ HReadonly ROMMON initialized" {9 A- B- x2 k; W4 ~# F
boot: cannot open "flash:"6 d9 n5 ~& }! r
boot: cannot determine first executable file name on device "flash:"
" k$ h, o, l7 b M6 R gc2811 processor with 262144 Kbytes of main memory" T, r! E" c% r2 K" y" [
Main memory is configured to 64 bit mode with ECC enabled
9 F- N/ R& t) R+ u) F" x% x% b5 h) }8 t6 s
; `! Q+ h2 h- t# R4 f H- h4 qReadonly ROMMON initialized
% {( j6 _7 M4 Z+ [rommon 1 > dir flash:
* V9 ?' ?3 B+ j, M" ~dir: cannot open device "flash:"
& u. J( @, c( d( z e- s- j; W' jrommon 2 >9 n$ K+ [! Y! G. T- _# U
$ _. b* z# I0 f W; V, q) e) |重灌IOS后也是看不到Flash
6 P; V) [# R. j1 \ t" h9 E: QR2#show flash:, \! a$ D, j2 z% |
0K bytes of ATA CompactFlash (Read/Write) |
2 [3 h i" r. y. q/ O3 v% k/ |, c |
|