设为首页收藏本站language 语言切换
查看: 2199|回复: 6
收起左侧

关于反向telnet,请路过的大虾指教

[复制链接]
发表于 2014-2-21 22:14:02 | 显示全部楼层 |阅读模式
用29路由器做服务器搭建了个机架,八爪线连接了四台35交换机,做好反向telnet配置后,输入"sw1",一直卡在下面这个画面:
Router#sw1
Trying sw1 (1.1.1.1, 2019)... Open
一直都是这样啊有木有,都好几天了有木有
物理连接应该没错,路由器配置信息和版本信息分别如下,请路过的大虾指教,不胜感谢。。。

Router#sh run            
Building configuration...                        
Current configuration : 2127 bytes                                 
!
! Last configuration change at 07:18:14 UTC Fri Feb 21 2014                                                           
!
version 15.0            
service timestamps debug datetime msec                                      
service timestamps log datetime msec                                    
no service password-encryption                              
!
hostname Router               
!
boot-start-marker                 
boot-end-marker               
!
!
no aaa new-model               
!
no ipv6 cef           
ip source-route               
ip cef      
!
!
!
!
no ip domain lookup                  
ip host sw1 2019 1.1.1.1                        
ip host sw2 2020 1.1.1.1                        
ip host sw3 2021 1.1.1.1                        
ip host sw4 2022 1.1.1.1                        
multilink bundle-name authenticated                                   
!
!
!
!
!
!
!
voice-card 0            
!
!
!
!
!
!
license udi pid CISCO2911/K9 sn FHK1439F375                                          
hw-module pvdm 0/0                  
!
!
!
!
redundancy         
!
!
!
!
!
!
interface Loopback0                  
ip address 1.1.1.1 255.255.255.255                                   
!
interface GigabitEthernet0/0                           
no ip address              
shutdown         
duplex auto            
speed auto           
!
interface GigabitEthernet0/1                           
no ip address              
shutdown         
duplex auto            
speed auto           
!
interface GigabitEthernet0/2                           
no ip address              
shutdown         
duplex auto            
speed auto           
!
interface Async0/1/0                    
no ip address              
encapsulation slip                  
!
interface Async0/1/1                    
no ip address              
encapsulation slip                  
!
interface Async0/1/2                    
no ip address              
encapsulation slip                  
!
interface Async0/1/3                    
no ip address              
encapsulation slip                  
!
interface Async0/1/4                    
no ip address              
encapsulation slip                  
!
interface Async0/1/5                    
no ip address              
encapsulation slip                  
!
interface Async0/1/6                  
no ip address              
encapsulation slip                  
!
interface Async0/1/7                    
no ip address              
encapsulation slip                  
!
interface Async0/1/8                    
no ip address              
encapsulation slip                  
!
interface Async0/1/9                    
no ip address              
encapsulation slip                  
!
interface Async0/1/10                     
no ip address              
encapsulation slip                  
!
interface Async0/1/11                     
no ip address              
encapsulation slip                  
!
interface Async0/1/12                     
no ip address              
encapsulation slip                  
!
interface Async0/1/13                     
no ip address              
encapsulation slip                  
!
interface Async0/1/14                     
no ip address              
encapsulation slip                  
!
interface Async0/1/15                     
no ip address              
encapsulation slip                  
!
ip forward-protocol nd                     
!
no ip http server                 
no ip http secure-server                        
!
!
!
!
!
control-plane            
!
!
!
!
!
!
!
!
gatekeeper
shutdown
!
!
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line 0/1/0 0/1/15
no exec
transport input all
line vty 0 4
login
!
scheduler allocate 20000 1000
end


Router#sh ver            
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M3, REL                                                                                
EASE SOFTWARE (fc2)                  
Technical Support: http://www.cisco.com/techsupport                                                   
Copyright (c) 1986-2010 by Cisco Systems, Inc.                                             
Compiled Sun 18-Jul-10 03:32 by prod_rel_team                                             
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)                                                                 
Router uptime is 36 minutes                           
System returned to ROM by power-on                                 
System image file is "flash0:c2900-universalk9-mz                                                
Last reload type: Normal Reload                              
This product contains cryptographic features and is subject to United                                                                     
States and local country laws governing import, export, transfer and                                                                    
use. Delivery of Cisco cryptographic products does not imply                                                            
third-party authority to import, export, distribute or use encryption.                                                                     
Importers, exporters, distributors and users are responsible for                                                               
compliance with U.S. and local country laws. By using this product you                                                                     
agree to comply with applicable laws and regulations. If you are unable                                                                       
to comply with U.S. and local laws, return this product immediately.                                                                    
A summary of U.S. laws governing Cisco cryptographic products may be found at:                                                                              
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html                                                      
If you require further assistance please contact us by sending email to                                                                       
export@cisco.com.                 
Cisco CISCO2911/K9 (revision 1.0) with 483328K/40960K bytes of memory.                                                                     
Processor board ID FHK1439F375                              
3 Gigabit Ethernet interfaces                             
16 terminal lines                 
DRAM configuration is 64 bits wide with parity enabled.                                                      
255K bytes of non-volatile configuration memory.                                                
254464K bytes of ATA System CompactFlash 0 (Read/Write)                                                      
License Info:            
License UDI:
-------------------------------------------------
Device#   PID                   SN
-------------------------------------------------
*0        CISCO2911/K9          FHK1439F375
Technology Package License Information for Module:'c2900'
----------------------------------------------------------------
Technology    Technology-package          Technology-package
              Current       Type          Next reboot
-----------------------------------------------------------------
ipbase        ipbasek9      Permanent     ipbasek9
security      None          None          None
uc            uck9          Permanent     uck9
data          None          None          None
Configuration register is 0x2102

Router#sh line              
   Tty Line Typ     Tx/Rx    A Modem  Roty AccO AccI  Uses  Noise Overruns  Int                                                                              
*     0    0 CTY              -    -      -    -    -     0      0    0/0      -                                                                                
      1    1 AUX   9600/9600  -    -      -    -    -     0      0    0/0      -                                                                                
  0/1/0   19 TTY   9600/9600  -    -      -    -    -     0      0                                                                        
  0/1/1   20 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -                                                                                
  0/1/2   21 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -                                                                                
  0/1/3   22 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -                                                                                
  0/1/4   23 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -                                                                                
  0/1/5   24 TTY   9600/9600  -    -      -    -    -     0      2    0/0      -                                                                                
  0/1/6   25 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -                                                                                
  0/1/7   26 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -                                                                                
  0/1/8   27 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
  0/1/9   28 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
0/1/10   29 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
0/1/11   30 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
0/1/12   31 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
0/1/13   32 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
0/1/14   33 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
0/1/15   34 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
    388  388 VTY              -    -      -    -    -     0      0    0/0      -
    389  389 VTY              -    -      -    -    -     0      0    0/0      -
    390  390 VTY              -    -      -    -    -     0      0    0/0      -
    391  391 VTY              -    -      -    -    -     0      0    0/0   




截图

截图
 楼主| 发表于 2014-2-25 11:09:37 | 显示全部楼层
一周了,还是没搞定
板凳 2014-2-25 11:09:37 回复 收起回复
回复 支持 反对

使用道具 举报

 楼主| 发表于 2014-2-25 11:12:09 | 显示全部楼层
论坛里肯定有人在用啊,还是帖子发的位置不对
地板 2014-2-25 11:12:09 回复 收起回复
回复 支持 反对

使用道具 举报

 楼主| 发表于 2014-2-25 16:24:02 | 显示全部楼层
看了cisco的官方材料(Configuring a Terminal/Comm Server,Document ID: 5466),好像只有2511 router ,2600 and 3600 series routers(加模块)支持这种功能,29是不行的。
就这样吧,给以后遇到同样问题的朋友一个参考。
原档见附件

5466-comm-server.pdf

28.73 KB, 下载次数: 20, 下载积分: 鸿鹄币 -1 个

5# 2014-2-25 16:24:02 回复 收起回复
回复 支持 反对

使用道具 举报

发表于 2016-1-2 12:52:04 | 显示全部楼层
正确啊,你要登陆的设备没有设置密码吧?
7# 2016-1-2 12:52:04 回复 收起回复
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 论坛注册

本版积分规则

QQ|Archiver|手机版|小黑屋|sitemap|鸿鹄论坛 ( 京ICP备14027439号 )  

GMT+8, 2025-2-12 18:16 , Processed in 0.068316 second(s), 24 queries , Redis On.  

  Powered by Discuz!

  © 2001-2025 HH010.COM

快速回复 返回顶部 返回列表