CCNA640-802：EIGRP实验真题详解

msvdm

                                                          CCNA640-802：EIGRP实验真题详解

---

LAB: EIGRP
Question#
After adding RTR_2 router, no routing updates are being exchanged between RTR_1 and the new location. All other inter connectivity and internet access for the existing locations of the company are working properly.

The task is to identify the fault(s) and correct the router configuration to provide full connectivity between the routers.
Access to the router CLI can be gained by clicking on the appropriate host.
All passwords on all routers are cisco .
IP addresses are listed in the chart below.

提示
排错要求：全网使用EIGRP路由协议，ISP不能配置全网内部所有设备互通所有主机和路由器可以ping通ISP上的回环接口故障提示：EIGRP的AS系统不一致可能导致故障EIGRP分发默认路由故障EIGRP宣告网络的相关故障故障排除后注意保存配置常用排错命令：ping show ip inter brishow ip protocolshow ip eigrp neishow ip routeshow run

[size=85%]RTR_A#show run
!
!
interface FastEthernet0/0
ip address 192.168.60.97 255.255.255.240
!
interface FastEthernet0/1
ip address 192.168.60.113 255.255.255.240
!
interface Serial0/0
ip address 192.168.36.14 255.255.255.252
clockrate 64000
!

router eigrp 212
network 192.168.36.0
network 192.168.60.0
no auto-summary
!

RTR_A#show ip route
192.168.36.0/30 is subnetted, 1 subnets
C 192.168.36.12 is directly connected, Serial 0/0
192.168.60.0/24 is variably subnetted, 5 subnets, 2 masks
C 192.168.60.96/28 is directly connected, FastEthernet0/0
C 192.168.60.112/28 is directly connected, FastEthernet0/1
D 192.168.60.128/28 [ 90/21026560 ] via 192.168.36.13, 00:00:57, Serial 0/0
D 192.168.60.144/28 [ 90/21026560 ] via 192.168.36.13, 00:00:57, Serial 0/0
D 192.168.60.24/30 [ 90/21026560 ] via 192.168.36.13, 00:00:57, Serial 0/0
D* 198.0.18.0 [ 90/21026560 ] via 192.168.36.13, 00:00:57, Serial 0/0

********************************************************************************

RTR_2#show run
!
!
interface FastEthernet0/0
ip address 192.168.77.34 255.255.255.252
!
interface FastEthernet0/1
ip address 192.168.60.65 255.255.255.240
!
interface FastEthernet1/0
ip address 192.168.60.81 255.255.255.240
!
!

router eigrp 22
network 192.168.77.0
network 192.168.60.0
no auto-summary
!

RTR_2#show ip route
192.168.60.0/28 is variably subnetted, 2 subnets
C 192.168.60.80 is directly connected, FastEthernet1/0
C 192.168.60.64 is directly connected, FastEthernet0/1
192.168.77.0/30 is subnetted, 1 subnets
C 192.168.77.32 is directly connected, FastEthernet0/0

**********************************************************

RTR_B#show run
!
interface FastEthernet0/0
ip address 192.168.60.129 255.255.255.240
!
interface FastEthernet0/1
ip address 192.168.60.145 255.255.255.240
!
interface Serial0/1
ip address 192.168.60.26 255.255.255.252

!

router eigrp 212
network 192.168.60.0
!

RTR_B#show ip route
192.168.60.0/24 is variably subnetted, 5 subnets, 2 masks
C 192.168.60.24/30 is directly connected, Serial0/1
C 192.168.60.128/28 is directly connected, FastEthernet0/0
C 192.168.60.144/28 is directly connected, FastEthernet0/1
D 192.168.60.96/28 [ 90/21026560 ] via 192.168.60.25, 00:00:57, Serial 0/1
D 192.168.60.112/28 [ 90/21026560 ] via 192.168.60.25, 00:00:57, Serial 0/1
192.168.36.0/30 is subnetted, 1 subnets
D 192.168.36.12 [ 90/21026560 ] via 192.168.60.25, 00:00:57, Serial 0/1
D* 198.0.18.0 [ 90/21026560 ] via 192.168.60.25, 00:00:57, Serial 0/1

**************************************************************************


RTR_1#show run
!
!
interface FastEthernet0/0
ip address 192.168.77.33 255.255.255.252
!
interface Serial1/0
ip address 198.0.18.6 255.255.255.0
!
!
interface Serial0/0
ip address 192.168.36.13 255.255.255.252
clockrate 64000
!
interface Serial0/1
ip address 192.168.60.25 255.255.255.252
clockrate 64000
!
!

router eigrp 212
network 192.168.36.0
network 192.168.60.0
network 192.168.85.0
network 198.0.18.0
no auto-summary
!
ip classless
ip default-network 198.0.18.0
ip route 0.0.0.0 0.0.0.0 198.0.18.5
ip http server

RTR_1#show ip route
192.168.36.0/30 is subnetted, 1 subnets
C 192.168.36.12 is directly connected, Serial 0/0
192.168.60.0/24 is variably subnetted, 5 subnets, 2 masks
C 192.168.60.24/30 is directly connected, Serial0/1

D 192.168.60.128/28 [ 90/21026560 ] via 192.168.60.26, 00:00:57, Serial 0/1
D 192.168.60.144/28 [ 90/21026560 ] via 192.168.60.26, 00:00:57, Serial 0/1
D 192.168.60.96/28 [ 90/21026560 ] via 192.168.36.14, 00:00:57, Serial 0/0
192.168.77.0/30 is subnetted, 1 subnets
C 192.168.77.32 is directly connected, FastEthernet0/0
C 192.0.18.0/24 is directly connected, Serial 1/0
*S 0.0.0.0 via 198.0.18.5

Explanation:
Step1:
Identify the faults in configuration on RTR_1 and RTR_2. As the SIM specifies all other inter connectivity and internet access for the existing locations of the company are working properly.

Routing Protocols used in the SIM is EIGRP with AS 212 as provided by exhibit.
Faults Identified:

• Wrong AS (EIGRP 22) provided at RTR_2 (New router)
• RTR_1 does not advertise the new network between RTR_1 and RTR_2 into EIGRP.
  

We need to correct the above two configuration mistakes to have full connectivity
Step2: Correcting the EIGRP AS to 212
Wrong AS (EIGRP 22) provided at RTR_2 (New router)
All routers that want to exchange routes within EIGRP needs to be in same Autonomous System.

Step 2.1:
First we need to remove the current wrong EIGRP AS 22 from Router RTR_2
Click on Host-F to get CLI of RTR_2

RTR_2>enable
Password : cisco (Provided by SIM Q )
RTR_2#conf t
RTR_2(conf)#
Step 2.2:
Removing the wrong EIGRP routing process with AS 22
RTR_2(conf)#no router eigrp 22
The above statement removes all the EIGRP configuration configured for AS 22 .

Step 2.3:
Adding the correct EIGRP configuration
Start the EIGRP routing process with AS 212
RTR_2(conf)#router eigrp 212
Step 2.4:
Advertise the directly connected networks into EIGRP on RTR_2

Fa 0/0 - 192.168.77.34
Fa 1/0 - 192.168.60.81
Fa 0/1 - 192.168.60.65

RTR_2(config-router)#network 192.168.60.0

RTR_2(config-router)#network 192.168.77.0
RTR_2(config-router)#no auto-summary
RTR_2(config-router)#end

Step 2.5:

Important save the changes made to router RTR_2
RTR_2#copy run start

Step 3:

RTR_1 does not advertise the new network between RTR_1 and RTR_2 into EIGRP.

Click on Host-G to get CLI of RTR_1
The network 192.168.77.0 is used between RTR_1 Fa0/0 - RTR_2 Fa 0/0
This network needs to be advertise into EIGRP routing process at RTR_1
RTR_1>enable
Password : cisco (Provided by SIM Q )
RTR_1#conf t
RTR_1(conf)#
Step 3.1:
Enter EIGRP routing process for AS 212
RTR_1(conf)#router eigrp 212

Step 3.2:
The network 192.168.77.0 is used between RTR_1 Fa0/0 - RTR_2 Fa 0/0 . Advertise this network into EIGRP
RTR_1(config-router)#network 192.168.77.0
RTR_1(config-router)#end

Step 3.3:
Important save the changes made to router RTR_1
RTR_1#copy run start

Verification:

From RTR_2 CLI
ping RTR_1 Serial 1/0 IP address 198.0.18.6
RTR_2#ping 198.0.18.6
!!!!!
A successful ping shows the new RTR_2 will have full connectivity with other routers.

Any Questions are welcomed!!!!!