642-902 5.14 pass (all lab details) taiwan_stn posted

stn

2 x2 S% E, _; S5 ~9 ^& E
/ W9 |3 o  A2 v" k: hthanks for this forum and v200,this dump is very perfect,
  L3 p, |, B$ PI want to share my test review：
9 W5 ~! ]- d7 [: D$ A# b5 Y! U6 ?I meet LAB about:
EIGRP OSPF Redistribute,PBR,IPV6 ospf virtual link and OSPF stub
1 \) I/ `, u1 d* Cabout EIGRP OSPF Redistribute:
3 L# X; |# _  {* A/ @# a1.the Area number,OSPF process and EIGRP process are the same with dump.
% D" S5 Q1 k8 H+ I, s5 }* w2.you must do this "distance eigrp 90 109" on router eigrp 100. I got this lab 100%
3.all the router interface ip address was changed.notice it.
) A, b7 b0 m) s8 ^3 z/ B6 ?4.after finish set.you can use "traceroute 172.16.100.1" on R1 to check the package through path.(R1-R2-R3-R4)
5.can't not copy run start
about PBR:
1.at first if you don't do anything,the Host for testing also can print 9 package.but you still set it follow dump.
2.the "route-map pbr permit 20" not to be set is ok . I got this lab 100%
3.ISP 1 IP address has been change is 10.1.101.2,carefully
4.can't not copy run start
about IPV6 ospf virtual link:all the same with dump.can't not copy run start.I got this lab 100%
0 Z) B1 e4 }5 P, O$ J, Qabout OSPF stub:
7 _/ @: ]+ L. X" e; V1.Route NAME & Area number & OSPF process was changed.be careful!!!!
% @& s1 e, d- P) E; u# }2.network address the same as dump(192.168.4.5,192.168.4.6)
+ y+ F1 `9 ^# S* g3.can copy run start.don't forgot it.I got this lab 100%
8 Y, ]3 ?& S- o' Z# Wthe others:
1 H" ~" O& b8 M" ND&D same with dump
I also meet some new questions(this is partial of questions,and I print it brief and short summary,Don't blame me)
(2011/5/15 update: I found it on the 642-901 dump)
" k8 Y+ c( [- e* N0 O3 z9 g& _1.All routers in the diagram are configured with EIGRP.If RTB and RTC fail, which action will RTA take with respect to the HQ network?
A.RTA will automatically route packets via RTD to the HQ network.
! z5 {9 _4 c9 ]  NB.RTA will place the route via RTD into the hold down state.
' l  v0 x' i2 L; p/ }C.RTA will go into the active state for all routers.
; Z  H1 F- E0 K. U. L( }) J+ PD.RTA will go into the active state for the route to HQ network.
& X' @* `1 u5 \8 o- rI choice D and finally report print is right,because I got this topic 100%
2 z9 N3 z6 o6 F! z2.Based on the topology shown in the network diagram, what optional EIGRP configurations will be required in order to achieve full connectivity within AS 100?
A.Use the EIGRP no auto-summary command on R1 and R2.
B.Use the EIGRP no auto-summary command on R3 and R4.
& l  I* Q6 D) LC.Use the passive interface on the R1 and R2 interface that connects to the 10.1.1.0/24 and 10.1.2.0/24 subnet respectively.
D.Use the passive interface command between the R3 and R1 connection and between the R3 and R2 connection.
3 g+ E& O8 x- ~. tE.Use the variance command on R3.
# {; s+ k2 N7 rAnswer is A
& c' ]* m' q, I, bThanks for this forum and v200 again!!!
: O  W+ A0 \7 }1 p4 C有任何问题也可以提问，我会尽量答的！
% I0 E! ^8 [' R7 x( c  {. q- `+ i! v& w

fulltimes

thanks for share

ciscohe

thank you

wende376

xjhaitun

刘小娜

fuck
  k: B3 f- j& L9 ?) v all  is  English

chantor5

恭喜楼主

531414213

能解释一下，为什么要R2上修给管理距离么？！

corcol08

stn

回复 531414213 的帖子

这道题有两个要求，第一个是要ping通，第二个是要用最有效的链路确保利用最大带宽，就是要走下面的快速以太网链路，所以要在R2上修改管理距离

531414213

回复 stn 的帖子

原来如此。题库上给的拓,EIGRP内网链路是串行线，有的人把修改管理距离解释为保证一条冗余路径，搞得我稀里糊涂的。谢谢

buishithahaha

Congratulations!!