Recent Passed

丝路明珠

Hello,
4 |  Y/ K. [  y0 j
I recently passed my exams last week:
9 k( [( M7 S& V, a  K' b
6 ]/ r" e+ f8 [- z( O( }$ X, zTS-New
5 u3 s/ m* X' e0 k' s-----------------------
. Y+ C1 o9 A- o. QTask 1: Adding a second vlan filter to forward traffic
+ X) R' _" e" S" c  i5 T. m
Task 2: Added next-hop-self on both R14 and R15

. S0 X; }: ]# C# s1 x: eTask 3: Played with metric to get the loadbalance and also corrected acls on R12 and R13...Also don't worry much about the order in which the the load balance happens as even in the output of the traces in the question,the order of the loadbalance was varying! Just make sure it load balances via the right devices!

2 L8 ^) F8 o4 p1 Y7 XTask 4:Route-map was already configured for both R20 and R21 for the specified prefix,just add to increase the local preference being sent by R21

Task 5: Correct route-target imports on R3 and R5, enable the lo0 on R1 in ospf, correct ospf network-type to point-to-multipoint on R14,R51
2 ~8 Z0 n7 K7 ?- o
+ ~7 j4 N. e& N: b" Y* v5 t7 E* K3 ?Task 6: Correct network type for DMVPN on R60 and ospf will come up

Task 7: Added the ipv6 network of R14 or R15's inside network in BGP

Task 8: ip dhcp relay information-trusted on both sw301 and sw302
5 L8 M5 d8 N- U6 @
* r1 t9 p) S7 e5 n+ b2 [Task 9: correct the tunnel key on R71
  f7 }% G4 T* Z- L
8 _9 e6 x' O/ O; Z& V1 u$ a* ^: eTask 10: Remove the wrong "ip nat source statement" and corrected the ip nat outside statement on both R24 and R25
3 k+ ?8 x8 X0 |

) J( Y+ X' n' m% D, l/ o8 Q0 XDIAG
3 @  }7 ^9 d1 F& P6 u: ?1 \) j-----------------
Multicast with site 3 having issue
  W) N% [  h2 i% z! a; t0 n/ SIPV6 HSRP with CE2 having the lower HSRP priority but higher preference
! W3 }% c3 Y4 W# q, g8 k
+ \( x7 N7 R& q4 G
, C2 L4 t3 X2 q' c8 cConfig:
4 w  v8 P" p( \# G# e& n-----------
! v! b* \# o/ K  s8 I3 K& k0 ^OLD config with vrf . Not much to mention with this as it's been discussed and shared here several times. Just a few things:
4 V- J$ f& J/ k
sw 1 and sw2 transparent mode ; sw3 server,sw4 client....Both sw 2 and sw 3 had no ports assigned to any vlans,you gotta sort that one out
9 G" x5 O+ c# n" m7 \0 r' Y3 v4 r
+ x/ X( g/ P) c* c" B5 ?For the multicast section,there's a requirement to put all unused ports on sw5 in vlan 5

There was no requirement for traffic from R12/R13/R14 to 1.2.3.4 to go via a certain interface on R20. There was only a ping and no traceroute.

VRFs were pre-configured

, h0 X3 q0 y: y+ \8 f2 XNTP was preconfigured,the question i got only stated to authenticate R10 and R12 using certain key. So configure the authentication on sw3,R10 and R12.

Other bits are already discussed here several times...
* ~$ j2 B4 m. N# R& ]- L9 W* |
A few other bits:
2 ?1 e7 V4 x0 q+ s6 _$ }4 L----------------------

Get used to not using tabbed terminals before the exam; Get used to waiting 3 to 5 seconds before what you've implemented actually takes effect! Don't panic after a second of sending certain prefixes and it hasn't been sent after 2 seconds. For the TS,when changing anything,give it a few seconds to take effect as well.
/ ]$ c7 H7 Q9 X/ S( B5 P6 _
# M3 j+ l% X8 e7 P$ q5 qverify,verify and verify what you've configured as you go along and also read through the questions after "finishing" your config. I missed out a question in my case and was able to implement it during verification.

$ N9 a' S% X* H: y9 w+ ?4 ?The lease time on a few of the  DHCP servers in TS were set to 2hrs, I did change them to 2 days just to be safe. It doesn't hurt to change this especially as you're not breaking any restrictions!
; [7 _% z; d, k& c3 K
Thanks a lot guys and all the best!

saadnwz

saadnwz

saadnwz

nxplmdy

歪个楼，300收17年LAB发票，有的单播QQ121463065

jamesscooby

Thank your share!