H3C 单臂路由

旭旭蟹

PC1与PC2分别可以PING通自己的网关，但是无法跨vlan通信

[SW]vlan 10

[SW-vlan10]vlan 20

[SW-vlan20]quit

[SW]inter g1/0/1

[SW-GigabitEthernet1/0/1]port link-type access

[SW-GigabitEthernet1/0/1]port access vlan 10

[SW-GigabitEthernet1/0/1]inter g1/0/2

[SW-GigabitEthernet1/0/2]port link-type access

[SW-GigabitEthernet1/0/2]port access vlan 20

PC1与PC2配置两条默认路由

[H3C]sys Router
[Router]inter g0/0.1
[Router-GigabitEthernet0/0.1]ip add 192.168.1.1 24
[Router-GigabitEthernet0/0.1]vlan-type dot1q vid 10
[Router-GigabitEthernet0/0.1]inter g0/0.2
[Router-GigabitEthernet0/0.2]ip add 192.168.2.1 24
[Rout[Router-GigabitEthernet0/0.2]vlan-type dot1q vid 20
[Router-GigabitEthernet0/0.2]quit

z247386032

Rockyw

路过了解一下

wlcbhrss

wlcbhrss

华为、H3C、思科这三家的命令都不一样，
思科： encapsulation dot1Q 200
华为：dot1q termination vid 100
         arp broadcast enable
H3C： vlan-type dot1q vid 42

wlcbhrss

在R1配置
interface GigabitEthernet0/0/0
#
interface GigabitEthernet0/0/0.10
dot1q termination vid 10
ip address 10.1.12.1 255.255.255.0
arp broadcast enable
#
interface GigabitEthernet0/0/0.20
dot1q termination vid 20
ip address 10.1.13.1 255.255.255.0
arp broadcast enable

interface LoopBack0
ip address 10.1.100.100 255.255.255.0
#
ip route-static 10.3.3.0 255.255.255.0 10.1.12.2
ip route-static 10.4.4.0 255.255.255.0 10.1.13.3

在交换机上配置
vlan batch 10 20
interface Ethernet0/0/1
port link-type trunk
port trunk allow-pass vlan 10 20
#
interface Ethernet0/0/2
port link-type trunk
port trunk allow-pass vlan 10 20
#
interface Ethernet0/0/3
port link-type trunk
port trunk allow-pass vlan 10 20

在AR3上配置
interface GigabitEthernet0/0/0.10
dot1q termination vid 10
ip address 10.1.12.2 255.255.255.0
arp broadcast enable
#
interface GigabitEthernet0/0/1
#
interface GigabitEthernet0/0/2
#
interface NULL0
#
interface LoopBack0
ip address 10.3.3.3 255.255.255.255
#
ip route-static 0.0.0.0 0.0.0.0 10.1.12.1
在AR4配置
interface GigabitEthernet0/0/0.20
dot1q termination vid 20
ip address 10.1.13.3 255.255.255.0
arp broadcast enable
#
interface GigabitEthernet0/0/1
#
interface GigabitEthernet0/0/2
#
interface NULL0
#
interface LoopBack0
ip address 10.4.4.4 255.255.255.255
#
ip route-static 0.0.0.0 0.0.0.0 10.1.13.1
#


[AR4]ping 10.3.3.3
  PING 10.3.3.3: 56  data bytes, press CTRL_C to break
    Reply from 10.3.3.3: bytes=56 Sequence=1 ttl=254 time=100 ms
    Reply from 10.3.3.3: bytes=56 Sequence=2 ttl=254 time=90 ms
    Reply from 10.3.3.3: bytes=56 Sequence=3 ttl=254 time=80 ms
    Reply from 10.3.3.3: bytes=56 Sequence=4 ttl=254 time=80 ms
    Reply from 10.3.3.3: bytes=56 Sequence=5 ttl=254 time=80 ms

  --- 10.3.3.3 ping statistics ---
    5 packet(s) transmitted
    5 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 80/86/100 ms

wlcbhrss

“[SW-GigabitEthernet1/0/1]port link-type access
[SW-GigabitEthernet1/0/1]port access vlan 10
[SW-GigabitEthernet1/0/1]inter g1/0/2
[SW-GigabitEthernet1/0/2]port link-type access
[SW-GigabitEthernet1/0/2]port access vlan 20”
应该封装为trunk
port link-type trunk
port trunk allow-pass vlan 10 20

若无

学习学习

若无

有详细的资料不

liprose

把静态路由做上就好了

caochentao

PC1：
interface GigabitEthernet1/0/1
port link-mode route
ip address 192.168.10.2 255.255.255.0
quit
ip route-static 0.0.0.0 0 192.168.10.1

PC2：
interface GigabitEthernet1/0/1
port link-mode route
ip address 192.168.20.2 255.255.255.0
quit
ip route-static 0.0.0.0 0 192.168.20.1

SW：
interface GigabitEthernet1/0/1
port link-mode bridge
port link-type trunk
port trunk permit vlan 1 10 20
quit
interface GigabitEthernet1/0/2
port link-mode bridge
port access vlan 10
quit
interface GigabitEthernet1/0/3
port link-mode bridge
port access vlan 20
quit
ROUTER：
interface GigabitEthernet0/0.10
ip address 192.168.10.1 255.255.255.0
vlan-type dot1q vid 10
quit
interface GigabitEthernet0/0.20
ip address 192.168.20.1 255.255.255.0
vlan-type dot1q vid 20
quit由于采用路由器模拟PC机，所以需要加一条默认路由，相当于PC上IP配置的网关。