关于832的万金油有个问题

oppodyv

第一轮看题：找出ospf v3和HSRP以及client 1 ipconfig 169.x.x.x的6道题，标记。从头到尾看一遍题目后，先解决ospf v3和HSRP，然后4道 169的每一道都确定原因后，对应上题库的4种，再作答。
第二轮看题：剩下7道中逐个在client 1 ping 网关，应该只有一个不通的，为vlan filter的，作答。
第三轮看题：剩下6道中逐个在client 1 ping R1--R2路由器接口的2个地址，有3种可能
                     1、ping都通---略过
                     2、ping R2通，R1不通，ospf 认证，作答
                     3、ping都不通---被动接口，重分布，看R4配置后作答
最后一轮：都在R1上 show run
                     BGP邻居宣告错
                     NAT
                     IP acl
                  错误特征都很明显，都确定后一起作答。



【上面说第二轮看题，PING 7次，总共一个CLIENT1 为什么要PING 7次】

oppodyv

又见好版主
那我直接在托普里PING
如果不通或者通再在TT里面选择不行吗

oppodyv

版主这个版本的题库是更新后正确答案吗

这个和实际的考试选项一样吗

请鉴定
TICKET 1 SWITCH PORT TRUNK
1- ASW1
2- Switch-to-Switch Connectivity
3- In Configuration mode, using the interface port-channel 13, port-channel 23, then configure switchport trunk allowed vlan none followed by switchport trunk allowed vlan 10,200 commands.

TICKET 2 ACCESS VLAN
1- ASW1
2- Access vlans
3- In Configuration mode, using the interface range Fastethernet 1/0/1 -2, then switchport access vlan 10 command.


TICKET 3 OSPF AUTHENTICATION
1- R1
2- IPv4 OSPF Routing
3- Enable OSPF Authentication on the S0/0/0 interface using the ip ospf authentication message-digest command.


TICKET 4 BGP Neighbor
1. R1
2. BGP
3. Under the BGP process, delete the neighbor 209.56.200.226 remote-as 65002 command and enter the neighbor 209.65.200.226 remote-as 65002 command.


TICKET 5 NAT ACL
4. R1
5. IP NAT
6. Under the ip access-list standar nat_trafic configuration enter the permit 10.2.0.0 0.0.255.255 command.


TICKET 6 R1 ACL
1. R1
2. IPv4 layer 3 security
3. Under the ip access-list extended edge_security configuration add the permit ip 209.65.200.224 0.0.0.3 any command.


TICKET 7 Port Security
1. ASW1
2. Port Security
3. In Configuration mode, using the interface range Fa 1/0/1 -2, then no switchport port-security,followed by shutdown,no shutdown interface configuration commands.


TICKET 8 Redistribution of EIGRP to OSPF
1. R4
2. IPv4 Router Redistribution
3. Under the EIGRP process, delete the redistribute ospf 1 router-map OSPF_to_EIGRP command enter the redistribute ospf 1 route-map OSPF->EIGRP command.


TICKET 9 EIGRP AS number
1. R4
2. IPv4 EIGRP Routing
3. Change the AS number on the EIGRP routing process from 1 to 10 to much the AS number used on DSW1 and DSW2.


TICKET 10 VLAN Access Map
1. DSW1
2. VLAN ACL / Port ACL
3. Under the global configuration mode enter no vlan filter test1 vlan-list 10 command.


TICKET 11 IPv6 OSPF
1. R2
2. IPv6 OSPF Routing
3. Under the interface Serial 0/0/0.23 configuration enter the ipv6 ospf 6 area 0 command.


TICKET 12 HSRP Issue
1. DSW1
2. HSRP
3. Under the interface vlan 10 configuration delete the standby 10 track 1 decrement 60 command and enter the standby 10 track 10 decrement 60 command.


TICKET 13 DHCP Issue Topology Overview
1. R4
2. IP DHCP Server
3. Under the IP DHCP pool configuration, issue the no ip dhcp excluded-address 10.2.1.1 10.2.1.253 command and enter the ip dhcp excluded-address 10.2.1.1 10.2.1.2 command.


TICKET 14 EIGRP Passive Interface
1. R4
2. IP EIGRP Routing
3. Under EIGRP Process enter no passive-interface fa0/0 and no passive interface fa0/1

oppodyv

送个大红花

woodward2012

楼主的思路比较清晰啊