华为ENSP中的STA无法获取地址
<AC1>display current-configuration#
sysname AC1
#
vlan batch 100 to 101
#
dhcp enable
#
interface Vlanif100
ip address 192.168.100.254 255.255.255.0
dhcp select interface
#
interface Vlanif101
ip address 192.168.101.254 255.255.255.0
dhcp select interface
#
interface MEth0/0/1
undo negotiation auto
duplex half
#
interface GigabitEthernet0/0/1
port link-type trunk
port trunk allow-pass vlan 100 to 101
#
capwap source interface vlanif100
#
wlan
traffic-profile name default
security-profile name default
security-profile name default-wds
security-profile name default-mesh
security-profile name lncc-security
security wpa-wpa2 psk pass-phrase %^%#+Rk}NbtjbM9|z%$Z+Wd5Ar'5B[A5SN[%gs&P2pq(
%^%# aes
ssid-profile name default
ssid-profile name lncc-ssid
ssid lncc
vap-profile name default
vap-profile name lncc-vap
service-vlan vlan-id 101
ssid-profile lncc-ssid
security-profile lncc-security
wds-profile name default
mesh-handover-profile name default
mesh-profile name default
regulatory-domain-profile name default
regulatory-domain-profile name lncc-domain
air-scan-profile name default
rrm-profile name default
radio-2g-profile name default
radio-5g-profile name default
wids-spoof-profile name default
wids-profile name default
wireless-access-specification
ap-system-profile name default
port-link-profile name default
wired-port-profile name default
serial-profile name preset-enjoyor-toeap
ap-group name default
ap-group name lncc-ap-group
regulatory-domain-profile lncc-domain
radio 0
vap-profile lncc-vap wlan 1
radio 1
vap-profile lncc-vap wlan 1
ap-id 1 type-id 45 ap-mac 00e0-fc66-07a0 ap-sn 210235448310FE291C23
ap-name AP1
ap-group lncc-ap-group
radio 0
channel 20mhz 1
eirp 10
radio 1
channel 20mhz 153
eirp 10
provision-ap
#
dot1x-access-profile name dot1x_access_profile
#
mac-access-profile name mac_access_profile
#
return
<AC1>
<LSW1>display current-configuration
#
sysname LSW1
#
vlan batch 100 to 101
#
interface GigabitEthernet0/0/1
port link-type trunk
port trunk pvid vlan 100
port trunk allow-pass vlan 100 to 101
#
interface GigabitEthernet0/0/2
port link-type trunk
port trunk allow-pass vlan 100 to 101
#
return
<LSW1>
<AC1>display ap all Info: This operation may take a few seconds. Please wait for a moment.done. Total AP information: nor: normal -------------------------------------------------------------------------------- ----------------- ID MAC Name Group IP Type State STAUptime -------------------------------------------------------------------------------- ----------------- 1 00e0-fc66-07a0 AP1lncc-ap-group 192.168.100.10 AP3030DN nor 0 - -------------------------------------------------------------------------------- ----------------- Total: 1 <AC1> csg_1 发表于 2019-7-31 13:45
display ap all Info: This operation may take a few seconds. Please wait for a moment.done. Total AP...
<AC1>display vap all
Info: This operation may take a few seconds, please wait.
WID : WLAN ID
-------------------------------------------------------------------------
AP ID AP name RfID WIDBSSID StatusAuth type STA SSID
-------------------------------------------------------------------------
1 AP1 0 1 00E0-FC66-07A0 ON WPA/WPA2-PSK0 lncc
1 AP1 1 1 00E0-FC66-07B0 ON WPA/WPA2-PSK0 lncc
-------------------------------------------------------------------------
Total: 2
<AC1> 本帖最后由 Rockyw 于 2019-7-31 14:02 编辑
路过了解一下！ 你这不是STA无法获取IP地址的问题吧，看你的配置基本上该配的都配了，按道理来说SSID应该放出来了才对，你的图上SSID没放出来，你是不是截图截早了？ 现在是SSID没放出来还是STA能连上SSID但是无法获取IP地址？ STA就没上来过的
STA>ipconfig
Link local IPv6 address...........: ::
IPv6 address......................: :: / 128
IPv6 gateway......................: ::
IPv4 address......................: 0.0.0.0
Subnet mask.......................: 0.0.0.0
Gateway...........................: 0.0.0.0
Physical address..................: 54-89-98-14-15-18
DNS server........................:
STA> 王赜 发表于 2019-7-31 14:02
你这不是STA无法获取IP地址的问题吧，看你的配置基本上该配的都配了，按道理来说SSID应该放出来了才对，你 ...
STA>ipconfig
Link local IPv6 address...........: ::
IPv6 address......................: :: / 128
IPv6 gateway......................: ::
IPv4 address......................: 0.0.0.0
Subnet mask.......................: 0.0.0.0
Gateway...........................: 0.0.0.0
Physical address..................: 54-89-98-14-15-18
DNS server........................:
STA>
没有地址的 csg_1 发表于 2019-7-31 14:14
STA>ipconfig
Link local IPv6 address...........: ::
你没懂我的意思，你得放出来SSID才能让STA去连SSID，你的图里AP根本就没放出来SSID，你的STA也没搜到SSID，怎么去获取IP地址？ 你把AP重启下重新上线应该就好了，我按你的配置配了，可以上线也可以获取到IP地址。 王赜 发表于 2019-7-31 14:21
你把AP重启下重新上线应该就好了，我按你的配置配了，可以上线也可以获取到IP地址。
重启了，还是上不来的，是不是我那个地方没做啊，STA1端没有任何反应的。 csg_1 发表于 2019-7-31 14:34
重启了，还是上不来的，是不是我那个地方没做啊，STA1端没有任何反应的。
AP端需要做什么不啊 e:\2.jpg csg_1 发表于 2019-7-31 14:35
AP端需要做什么不啊
加我Q，给你远程看看，289090326 csg_1 发表于 2019-7-31 14:40
帮忙看一下，多谢。
是不是dhcp参数没配置对？
页:
[1]